Need Affordable, No Contract, AlarmNet Monitoring From Just $11.95?

Technical Support Available 7 days a week!

CHECK 103 Long Range Radio XXXX

Check 103 Long Range Radio (LRR) followed by a 4 digit code is an error that shows up on Honeywell control panels if there is a problem with the cellular or IP communication associated with AlarmNet.

Cause for Error

Check 103 LRR could show up if the AlarmNet cell and/or IP radio loses contact with the alarm panel or more likely with AlarmNet. This usually occurs when there is a temporary cellular outage from your local LTE network. It could be routine tower maintenance or actual hardware problems with the carrier.

There is generally a 4 digit code after the Check 103 LRR which indicates where to begin your troubleshooting.

0000 – Control panel lost communication with the AlarmNet communicator
0880 – Tamper detected – The cover has been removed (opened) on the communicator.
0005 – Lost communication with the cell network. Honeywell communicators in the US use ATT or Verizon for service.
000F – Communicator is not registered, activate the radio/account with AlarmNet (dealer would do this).
0019 – Communicator Shutdown
0400 – Communicator power on/reset and the control panel lost communication with it
0C80 – Communicator power on/reset and tamper detected
08E0 – Communicator tamper detected and communicator battery is low
3000 – Primary power loss
8000 – Battery charger failure
0060 – Communicator low battery

How To Correct The Issue

Test the Communication. There is a possibility the cell towers had a temporary loss of communication with your alarm system’s cellular communicator but now the communication path is restored. Trip an alarm and be sure you get a call from the central station. If using Total Connect 2.0 also check to see if you can remotely arm and disarm. Usually the error goes away once communication with AlarmNet is restored but sometimes going into Program Mode then exit is required to remove the error message.
On a Vista panel enter [Installer Code] + 800. 4112 is the default Installer Code unless changed by the installer. “20” will appear on the keypad if in Program Mode. To exit just enter *99. The message should be gone if communication has been restored.

2. Power Cycle The Communicator/Panel. Many times a simple power down then power-up will resolve the issue.

Open the panel cover and locate the backup battery (large rectangle at bottom of panel).
Remove either the RED or BLACK wire from the backup battery.
Unplug the panel’s AC transformer from the wall 110VAC outlet. Many times the transformer is screwed in to the outlet so just loosen the screw and unplug.
Count to 10
Reconnect the backup battery.
Plug the AC transformer back in to the nearby 110VAC outlet..

If neither of these steps worked just reach out to your AlarmNet dealer such as SafeHomeCentral.com for assistance.

Honeywell AlarmNet No Contract Pricing Plans

* Pricing shown includes a 15% annual pre-pay discount. A one-time $15 activation fee applies to all new AlarmNet accounts.

* Requires an AlarmNet compatible communicator

Self

Smart Security

Mobile App Control

No Central Station Dispatch
$11.95 USD IP

$13.95 USD Cell
Internet, Cellular, Redundant Connectivity Options
Connect to AlarmNet and our UL Central Station via IP Internet/WIFI or optional Cellular or both for redundant communication paths.
No Contract
We offer all alarm monitoring plans with NO CONTRACTS. No long-term, multi-year commitments. We do offer pre-pay discounts for annual (15%) or just go month to month. Your choice and never any pressure to change.
Text and eMail Notifications
Push notifications of alarm events right to your phone, tablet, and/or PC. Includes Arm and Disarm, Trouble, AC Loss, etc.
APL
Advanced Protection Logic protects alarm signaling when an intruder destroys your security system during the entry delay period before an actual alarm is triggered. Works with all compatible Honeywell panels such as Lynx Touch and Lyric.
Daily Supervision
Monitor panel connectivity with signal supervision between the control panel and AlarmNet to know when a panel is not responding.
Remote Arming/Disarming
Arm/disarm system remotely via Total Connnect 2 web or mobile apps.
System Status and Summary of Recent Activity
View an at-a-glance summary showing the current system status and any recent activity at the property via web or mobile apps
User Code Management
Add/delete/edit user codes remotely, and track which users arm/disarm the system at what times. For systems with multiple partitions, choose which partition(s) each user code can access.
Searchable 90-Day Event History
Search a 90-day history of events reported by the system, including alarms and other activity, via web or mobile apps. Customize the time frame of the search, and filter by device or event type. Download results as HTML or Excel files.
Multiple Permission-Based Web Logins
Create different “sub-users” for the account and grant varying levels of permissions for each user to view/change various settings in the Total Connect 2 online account.
Multi-Site Access
Access multiple security systems from a single account through a convenient drop-down menu in the Total Connect 2 online account and mobile apps. Great for primary home and vacation home.
Alarms
Receive email/text message notifications for any type of alarm reported by the security system. These automated alarm alerts are in addition to the emergency response services provided by our UL central monitoring station.
Arming/Disarming
Receive email/text message notifications from Total Connect 2 when the security system is armed or disarmed. These messages are not forwarded to our UL central station for action of logging.
System Events
Receive email/text message notifications for power failures, sensor tampers and malfunctions, panel low battery, and other types of system events.
Geo-Services
Intelligently trigger arming reminders and events based on Geo-Fence settings and mobile phone location.
Sensor Activity Monitoring - 50 Sensors
Even when the security system is disarmed, receive email/text message notifications for non-alarm activity reported by sensors including: door, window, cabinet, motion, and other various sensors. Your system communicates ALL sensor and system activity that occurs 24/7 to AlarmNet's Network Operations Centers, then sends customized notifications to selected recipients.
Video Doorbell (Skybell models)
Includes remote viewing and interaction with a Honeywell Total Connect 2 video doorbell.
Amazon Echo Support
Ask Alexa to arm your security system or get status. Alexa can not disarm for security reasons.
Weather
Receive local weather on your Total Connect 2 app as well as compatible security system displays such as Lyric.

Self

Smart Home

Mobile App Control

No Central Station Dispatch
$15.95 USD IP

$17.95 USD Cell
Internet, Cellular, Redundant Connectivity Options
Connect to AlarmNet and our UL Central Station via IP Internet/WIFI or optional Cellular or both for redundant communication paths.
No Contract
We offer all alarm monitoring plans with NO CONTRACTS. No long-term, multi-year commitments. We do offer pre-pay discounts for annual (15%) or just go month to month. Your choice and never any pressure to change.
Text and eMail Notifications
Push notifications of alarm events right to your phone, tablet, and/or PC. Includes Arm and Disarm, Trouble, AC Loss, etc.
APL
Advanced Protection Logic protects alarm signaling when an intruder destroys your security system during the entry delay period before an actual alarm is triggered. Works with all compatible Honeywell panels such as Lynx Touch and Lyric.
Daily Supervision
Monitor panel connectivity with signal supervision between the control panel and Alarm.com to know when a panel is not responding.
Remote Arming/Disarming
Arm/disarm system remotely via Total Connect 2 web or mobile apps.
System Status and Summary of Recent Activity
View an at-a-glance summary showing the current system status and any recent activity at the property via web or mobile apps
User Code Management
Add/delete/edit user codes remotely, and track which users arm/disarm the system at what times. For systems with multiple partitions, choose which partition(s) each user code can access.
Searchable 90-Day Event History
Search a 90-day history of events reported by the system, including alarms and other activity, via web or mobile apps. Customize the time frame of the search, and filter by device or event type. Download results as HTML or Excel files.
Multiple Permission-Based Web Logins
Create different “sub-users” for the account and grant varying levels of permissions for each user to view/change various settings in the Total Connect 2 online account.
Multi-Site Access
Access multiple security systems from a single account through a convenient drop-down menu in the Total Connect 2 online account and mobile apps. Great for primary home and vacation home.
Alarms
Receive email/text message notifications for any type of alarm reported by the security system. These automated alarm alerts are in addition to the emergency response services provided by our UL central monitoring station.
Arming/Disarming
Receive email/text message notifications from Total Connect 2 when the security system is armed or disarmed. These messages are not forwarded to our UL central station for action of logging.
System Events
Receive email/text message notifications for power failures, sensor tampers and malfunctions, panel low battery, and other types of system events.
Geo-Services
Intelligently trigger arming reminders and events based on Geo-Fence settings and mobile phone location.
Sensor Activity Monitoring - Unlimited
Even when the security system is disarmed, receive email/text message notifications for non-alarm activity reported by sensors including: door, window, cabinet, motion, and other various sensors. Your system communicates ALL sensor and system activity that occurs 24/7 to AlarmNet's Network Operations Centers, then sends customized notifications to selected recipients.
Video Doorbell (Skybell models)
Includes remote viewing and interaction with a Honeywell Total Connect 2 video doorbell.
Amazon Echo Support
Ask Alexa to arm your security system or get status. Alexa can not disarm for security reasons.
Weather
Receive local weather on your Total Connect 2 app as well as compatible security system displays such as Lyric.
Smart Scenes
Smart Scenes offer convenient automationof security and comfort settings. Triggered Smart Scenes are initiated by the system in response to user defined conditions occurring. Scheduled Smart Scenes are initiated by the system’s calendar and clock.
Lights
Send commands to turn lights on/off via web or mobile apps. Create automated light schedules to have specific lights turn on at certain times, for specified lengths of time. Create rules so a specific light turns on if a certain sensor is activated.
Locks
Remotely control door locks via web or mobile apps, see lock status (locked/unlocked) and receive email/text message notifications when a lock is accessed by a specific user.
Thermostats
Remotely control thermostat(s) via web or mobile apps and easily create custom schedules to set temperatures based on time of day, day of week, activity patterns and the status of the security system to make properties run more efficiently
Garage Door Control
Remotely manage and control garage doors via web or mobile apps. View garage door status, receive garage door alerts and close automatically when system is armed. Chamberlain and LiftMaster support!

Dispatch

Security

No App Control

Central Station Dispatch
$13.95 USD IP

$15.95 USD Cell
Internet, Cellular, Redundant Connectivity Options
Connect to AlarmNet and our UL Central Station via IP Internet/WIFI or optional Cellular or both for redundant communication paths.
UL Central Station
We have trained operators ready to respond and verify your alarm signals 24x7x365. This includes burglary alarms, life safety such as fire and CO, status signals (AC loss), and environmental alerts such as low temperature or flood detection. Upto 75 zones of protection which is more than you'll ever need!
No Contract
We offer all alarm monitoring plans with NO CONTRACTS. No long-term, multi-year commitments. We do offer pre-pay discounts for annual (15%), six months (5%) or just go month to month. Your choice and never any pressure to change.
Alarm Monitoring Certificate
We supply you right away with a UL central station monitoring certificate for your insurance company so you can enjoy an annual discount on your premium, up to 20%!
Telephone Notification
Receive alarm notifications by telephone. The central station will notify you or a family member/relative, neighbor etc. from your Call List if authorities were dispatched.
APL
Advanced Protection Logic protects alarm signaling when an intruder destroys your security system during the entry delay period before an actual alarm is triggered. Works with all compatible Honeywell panels such as Lynx Touch and Lyric.
Daily Supervision
Monitor panel connectivity with signal supervision between the control panel and AlarmNet to know when a panel is not responding.

Dispatch

Smart Security

Mobile App Control

Central Station Dispatch
$15.95 USD IP

$17.95 USD Cell
Internet, Cellular, Redundant Connectivity Options
Connect to AlarmNet and our UL Central Station via IP Internet/WIFI or optional Cellular or both for redundant communication paths.
UL Central Station
We have trained operators ready to respond and verify your alarm signals 24x7x365. This includes burglary alarms, life safety such as fire and CO, status signals (AC loss), and environmental alerts such as low temperature or flood detection. Upto 75 zones of protection which is more than you'll ever need!
No Contract
We offer all alarm monitoring plans with NO CONTRACTS. No long-term, multi-year commitments. We do offer pre-pay discounts for annual (15%) or just go month to month. Your choice and never any pressure to change.
Alarm Monitoring Certificate
We supply you right away with a UL central station monitoring certificate for your insurance company so you can enjoy an annual discount on your premium, up to 20%!
Text and eMail Notifications
Push notifications of alarm events right to your phone, tablet, and/or PC. Includes Arm and Disarm, Trouble, AC Loss, etc.
Telephone Notification
Receive alarm notifications by telephone. The central station will notify you or a family member/relative, neighbor etc. from your Call List if authorities were dispatched.
APL
Advanced Protection Logic protects alarm signaling when an intruder destroys your security system during the entry delay period before an actual alarm is triggered. Works with all compatible Honeywell panels such as Lynx Touch and Lyric.
Daily Supervision
Monitor panel connectivity with signal supervision between the control panel and AlarmNet to know when a panel is not responding.
Remote Arming/Disarming
Arm/disarm system remotely via Total Connnect 2 web or mobile apps.
System Status and Summary of Recent Activity
View an at-a-glance summary showing the current system status and any recent activity at the property via web or mobile apps
User Code Management
Add/delete/edit user codes remotely, and track which users arm/disarm the system at what times. For systems with multiple partitions, choose which partition(s) each user code can access.
Searchable 90-Day Event History
Search a 90-day history of events reported by the system, including alarms and other activity, via web or mobile apps. Customize the time frame of the search, and filter by device or event type. Download results as HTML or Excel files.
Multiple Permission-Based Web Logins
Create different “sub-users” for the account and grant varying levels of permissions for each user to view/change various settings in the Total Connect 2 online account.
Multi-Site Access
Access multiple security systems from a single account through a convenient drop-down menu in the Total Connect 2 online account and mobile apps. Great for primary home and vacation home.
Alarms
Receive email/text message notifications for any type of alarm reported by the security system. These automated alarm alerts are in addition to the emergency response services provided by our UL central monitoring station.
Arming/Disarming
Receive email/text message notifications from Total Connect 2 when the security system is armed or disarmed. These messages are not forwarded to our UL central station for action of logging.
System Events
Receive email/text message notifications for power failures, sensor tampers and malfunctions, panel low battery, and other types of system events.
Geo-Services
Intelligently trigger arming reminders and events based on Geo-Fence settings and mobile phone location.
Sensor Activity Monitoring - 50 Sensors
Even when the security system is disarmed, receive email/text message notifications for non-alarm activity reported by sensors including: door, window, cabinet, motion, and other various sensors. Your system communicates ALL sensor and system activity that occurs 24/7 to AlarmNet's Network Operations Centers, then sends customized notifications to selected recipients.
Video Doorbell (Skybell models)
Includes remote viewing and interaction with a Honeywell Total Connect 2 video doorbell.
Amazon Echo Support
Ask Alexa to arm your security system or get status. Alexa can not disarm for security reasons.
Weather
Receive local weather on your Total Connect 2 app as well as compatible security system displays such as Lyric.

Dispatch

Smart Home

Mobile App Control

Central Station Dispatch
$19.95 USD IP

$21.95 USD Cell
Internet, Cellular, Redundant Connectivity Options
Connect to AlarmNet and our UL Central Station via IP Internet/WIFI or optional Cellular or both for redundant communication paths.
UL Central Station
We have trained operators ready to respond and verify your alarm signals 24x7x365. This includes burglary alarms, life safety such as fire and CO, status signals (AC loss), and environmental alerts such as low temperature or flood detection. Upto 75 zones of protection which is more than you'll ever need!
No Contract
We offer all alarm monitoring plans with NO CONTRACTS. No long-term, multi-year commitments. We do offer pre-pay discounts for annual (15%) or just go month to month. Your choice and never any pressure to change.
Alarm Monitoring Certificate
We supply you right away with a UL central station monitoring certificate for your insurance company so you can enjoy an annual discount on your premium, up to 20%!
Text and eMail Notifications
Push notifications of alarm events right to your phone, tablet, and/or PC. Includes Arm and Disarm, Trouble, AC Loss, etc.
Telephone Notification
Receive alarm notifications by telephone. The central station will notify you or a family member/relative, neighbor etc. from your Call List if authorities were dispatched.
APL
Advanced Protection Logic protects alarm signaling when an intruder destroys your security system during the entry delay period before an actual alarm is triggered. Works with all compatible Honeywell panels such as Lynx Touch and Lyric.
Daily Supervision
Monitor panel connectivity with signal supervision between the control panel and Alarm.com to know when a panel is not responding.
Remote Arming/Disarming
Arm/disarm system remotely via Total Connect 2 web or mobile apps.
System Status and Summary of Recent Activity
View an at-a-glance summary showing the current system status and any recent activity at the property via web or mobile apps
User Code Management
Add/delete/edit user codes remotely, and track which users arm/disarm the system at what times. For systems with multiple partitions, choose which partition(s) each user code can access.
Searchable 90-Day Event History
Search a 90-day history of events reported by the system, including alarms and other activity, via web or mobile apps. Customize the time frame of the search, and filter by device or event type. Download results as HTML or Excel files.
Multiple Permission-Based Web Logins
Create different “sub-users” for the account and grant varying levels of permissions for each user to view/change various settings in the Total Connect 2 online account.
Multi-Site Access
Access multiple security systems from a single account through a convenient drop-down menu in the Total Connect 2 online account and mobile apps. Great for primary home and vacation home.
Alarms
Receive email/text message notifications for any type of alarm reported by the security system. These automated alarm alerts are in addition to the emergency response services provided by our UL central monitoring station.
Arming/Disarming
Receive email/text message notifications from Total Connect 2 when the security system is armed or disarmed. These messages are not forwarded to our UL central station for action of logging.
System Events
Receive email/text message notifications for power failures, sensor tampers and malfunctions, panel low battery, and other types of system events.
Geo-Services
Intelligently trigger arming reminders and events based on Geo-Fence settings and mobile phone location.
Sensor Activity Monitoring - Unlimited
Even when the security system is disarmed, receive email/text message notifications for non-alarm activity reported by sensors including: door, window, cabinet, motion, and other various sensors. Your system communicates ALL sensor and system activity that occurs 24/7 to AlarmNet's Network Operations Centers, then sends customized notifications to selected recipients.
Video Doorbell (Skybell models)
Includes remote viewing and interaction with a Honeywell Total Connect 2 video doorbell.
Amazon Echo Support
Ask Alexa to arm your security system or get status. Alexa can not disarm for security reasons.
Weather
Receive local weather on your Total Connect 2 app as well as compatible security system displays such as Lyric.
Smart Scenes
Smart Scenes offer convenient automationof security and comfort settings. Triggered Smart Scenes are initiated by the system in response to user defined conditions occurring. Scheduled Smart Scenes are initiated by the system’s calendar and clock.
Lights
Send commands to turn lights on/off via web or mobile apps. Create automated light schedules to have specific lights turn on at certain times, for specified lengths of time. Create rules so a specific light turns on if a certain sensor is activated.
Locks
Remotely control door locks via web or mobile apps, see lock status (locked/unlocked) and receive email/text message notifications when a lock is accessed by a specific user.
Thermostats
Remotely control thermostat(s) via web or mobile apps and easily create custom schedules to set temperatures based on time of day, day of week, activity patterns and the status of the security system to make properties run more efficiently
Garage Door Control
Remotely manage and control garage doors via web or mobile apps. View garage door status, receive garage door alerts and close automatically when system is armed. Chamberlain and LiftMaster support!